Specification  (HS)

Feeding feature by PLC program from Mitsubishi:
1) NC Servo feeding. Operating with computerized numerical control by
   PLC program from Mitsubishi made in Japan. The electrical parts from
    YASKAWA made in Japan including Servo motor, driver, encoder, interface
    screen and so on
2) High precision feeding: to meet the coming of hi-tech industry, controlled
    by computer closed circuit feedback system to keep precision degree
    within ¡À0.03mm
3) Feeding function: input 20 sets of different feeding length, each
    group provides 999 times for punching or cutting to satisfy processing of
    special products
3) High efficiency release device, match with adjustment of signal from
    the cutter or press machine through cable wire
4) Setting of feeding length: directly input feeding length on the control
    plate, and then it can reach needed distance, feed length max. 9999.99mm,
    speed max. 100m/min

press features:
The body of JH21 series press is welded with steel plate,so it is with good rigidity
and stable precision.The crankshaft is placed lengthways,so the structure is
compact and the contour beautiful. Using the combined pneumatic friction clutch
and brake,so the engagement is smooth,the action agile,and the noise low.Gear pair
adopts the flooding system lubrication.The slide block is six-face rectangle
with longer guide track whose face is bronze panel.Meanwhile an import hydraulic
overload protector is installed in the slideblock whose air pump and high pressure
ring seal are imported from other country.Its action is agile and reliable.The
die set is adjusted by motor over JH21-63 press.There set lifting balance cylinder
at the slideblock over model JH2I-4O press,whose ring seal is imported from
other country.The air pipeline is controlled by safety duplex valve. Its electric
circuit is controled by import PLC.The press can be equipped with air cushion,
automatic feed shaft and photoelectric protector,and can be equipped with various
automatic equipment which conform to the safety standard of press.

specificatiom

mode	CLS-150	CLS-200	CLS-300	CLS-400	CLS-500	CLS-600	CLS-700	CLS-800
material width	150	200	300	400	500	600	700	800
material thickness	0.5-3	0.5-3	0.5-3	0.5-3	0.5-3	0.5-3	0.5-3	0.5-3
Decelerator	1/30	1/30	1/30	1/30	1/30	1/30	1/30	1/30
motor	1	1	1	2	2	3	3	5
feeding Rollers	60Ø*2 80Ø*2	60Ø*2 80Ø*2	60Ø*2 80Ø*2	70Ø*2 98Ø*2	70Ø*2 98Ø*2	70Ø*2 98Ø*2	70Ø*2 98Ø*2	70Ø*2 98Ø*2
straightening Rollers	50Ø*7	50Ø*7	50Ø*7	60Ø*7	60Ø*7	60Ø*7	60Ø*7	60Ø*7

Features

1.The unique openable bias rolls design.

2.the whole upper rollers can be opened

3.easy loading, feeding, cleaning and operation

4.The upper work rollers adop 4 point fine micro adjusters with reading 0.01 mm advance reference indicators, high quality and precision.

5.All rolls are made of bearing steel (SUJ2), have all been quenched, hard chrome plated and ground with min. HRC 60 degree.

7.Outgoing cantenary to assist and support the material.

8. Japanese bearings-high precision and durable. Add gear lubrication system. Quality guarantee.

specification

Item           Model	TLF-200	TLF-300	TLF-400	TLF-500	TLF-600
Coil Width(mm)	200	300	400	500	600
Coil Thickness(mm)	0.1-1.5			0.1-1.3	0.1-1.2
Invertor	provide
Straightener Motor (kw)	1kw	1kw	2kw	3kw	3kw
Straightener Roll (Qty)	upper8 /lower9 All driven function
Back up rolls	No		Provide
pinch roll(Qty)	upper1/lower1 All dreiven function
Loop Control	touch sensor
Speed Range ( m/min)	22m/min
thickness adjustment	4 points fine micro Adjustment

Straightening Performance

thickness(mm)	0.1	0.35	0.6	0.8	1	1.2	1.5
TLF-200	200mm				150mm	100mm	80mm
TLF-300	300mm			200mm	150mm	100mm	80mm
TLF-400	400mm				300mm	250mm	200mm
TLF-500	500mm				300mm	250mm	200mm
TLF-600	600mm				300mm	250mm	200mm

It is powerful new equipment, used in high-speed pressing; it can improve the quality and quantity of press workpieces. GJ two-section type straightening, the head is <--> during roll straightening , there is no need straightening in the midway. In order to get good performance, the rolling material has to be straightened

specification of JM3 series

(JM3 whole-section type straightener suitable for straightening of continoual rolling and slice material, its features are similar with that of one-section type)
 

Structure: output structure of straightening and materials, idler wheel feeding, idler wheel straightening and motor speed reducing; with the features of reasonable structure, firm, stable transmission and convenient operation

Application range: For straightening material rolls of various metal sheet; suitable for continuous production of hardware factory, electronic parts factory and press workpiece. Material thickness is 0.5-3.0mm